How to install Platinum Commercial Automatic Temperature Control Thermostatic Sensor Tap B505 Solid Brass Construction | SENSOR-TAP-FB505
Easy step by steps Installation Instructions for Commercial Sensor Faucet
|
|
|
Visit Product Page
|
- Before you begin, please read the installation instructions below. Observe all local building and safety codes.
- Unpack and inspect the touchless faucet for any shipping damagess for any shipping damages. If you find damages, do not install.
- Please note all products must be installed by a professional and certified plumber otherwise warranty might be voided.
|
sensor
|
|
|
Sensor Faucet Installations Instructions
Size:
|
|
|
|
|
|
Features:
- Cold and Hot integration. It is a mixer with the cold water in the left turning and hot water in the right turning.
- Water saving: Water flows out when your hands approach the induction zone, and stop immediately once you draw back your hands.
- Low power,electricity-saving: For DC type, 4pcs AA batteries can be used for about 2 years, if the faucet working 200 times a day.
Specification:
- Installation Type: Deck Mounted
- Installation Holes: One Hole
- Finish: Chrome Polished - Valve Type: Ceramic Valve
- Suitable Water Pressure: 0.3-1.2 MPa
- Temperature of environment:1-45°C (cold&hot water )
- Electric Power: DC Dry Battery
- Dia of inlet pipe: G1/2"
- Dia of outlet pipe: G1/2"
- Power: DC6V (4AA Alkaline batteries)
- Power consumption in static: <0.5 mW
- Detection Zone: Factory set 30cm
- Protection degree: IP56
Smart infrared sensor automatically adjusts the distance according to the environment.
|
|
|
|
|
|
|
|
|
Step 1: Battery Box
|
|
Step 2:
|
|
sensor
|
|
|
|
|
|
|
|
Step 3:
|
|
Step 4:
|
|
|
|
|
|
|
|
|
|
Step 5:
|
|
Step 6: Correct way for Hose
|
|
|
|
|
|
|
|
|
|
Before installing your new mixer, flush through the pipework to ensure removal of debris, turn off the water supply.
Ensure the ‘O’ ring is in place at the bottom of the mixer body.
Push the control cable down through the hole and position the mixer on the basin. From the underside of the basin fit the rubber washer, metal washer onto the threaded tube followed by the nut. Tighten the nut to clamp the mixer to the basin. Tighten the 2 side screws up onto the washer.
CAUTION: Do not over tighten the nut/bolts as this may damage the basin.
Screw the two flexible pipes to the mixer body, but do not over tighten, hand tighten only.
Connect the water supply to the inlet pipes. The hot water should be connected to the front pipe.
Plug together the connectors coming from the mixer to the transformer. Line up the flats on both the plug and socket and firmly push together.
Battery installation and replacement
The unit is supplied with a battery backup. Should the mixer will still not function then the batteries may need replacing. Before installing the mixer fit the supplied batteries as follows.
Unscrew the grub screw on the back of the mixer (do not remove) unscrew and remove the cover from the mixer and pull out the battery pack.
Undo the screw on the top of the battery pack and remove the lid. Insert the 4 batteries.
Place the battery pack back into the mixer, replace the cover and tighten the grub screw.
|
|
|
Flexible Connecting Hose Care must be taken when connecting the flexible connection hose from the power supply box to the spout to ensure it does not bend sharply and kink or twist. See above for recommended ways to fit the flexible connecting hose.
Important: Failure to follow these guidelines may result in poor performance and damage to the flexible connection hose.
|
|
|
Platinum Commercial Automatic Temperature Control Thermostatic Sensor Tap B505 Solid Brass Construction
The Fontana Temperature Control Platinum Thermostatic Touchless Bathroom Faucet is a touchless faucet that significantly reduces germ cross-contamination. Through the use of a sensor beam, the Touchless Bathroom Faucet determines when an object is in front of it and automatically turns on. Bathroom sensor faucets are anti-erosion, anti-abrasion and long-lasting. This sensor faucet is available in chrome. A great addition to bathrooms, medical facilities, hotels, restaurants, and other public facilities.
Features:
- Fits all standard US plumbing.
- Uses 4AA Alkaline Batteries (purchase separately).
- Water Pressure: 0.5 - 7.0 KGS/cm, 10-125 psi
- Sensor Faucet Applications: Residential & Commercial.
- Touchless Operation
- Sensitive Sensor with Infrared AI Smart-Chip
- Factory set to 30-second Auto Shutoff (can be adjusted).
- Water Pressure: 0.5 - 7.0 KGS/cm , 10 - 125 psi
- Solid Brass Construction, Polished Chrome Finish
- Easy to Install - Instructions Included
- Water-resistant solenoid enclosure
- Advanced energy-saving design for long-lasting battery life
- Comes complete with Hoses & Accessories
- ADA Compliant
- Easily can be installed in new or retrofit applications.
- Can easily be installed in new or retrofit applications
- Usage: Commercial / Residential
- Ideal for commercial use applications in public restrooms, restaurants, office building, public facilities, hospitals. Fits all standard US plumbing
|
|
Healthcare facilities have seen a prevalence of touchless faucets and automatic soap dispensers. Numerous hospitals have been incorporating these fixtures to uphold hygiene protocols.
We provide comprehensive solutions for latest touchless operation as traditional handle faucets can harbor germs, whereas touch-free operation in restrooms helps prevent the spread of germs.
The hospitality industry, as well as public and high traffic restrooms are experiencing a surge in demand for touchless faucets and automatic soap dispensers, driven by the growing need for hygiene and sanitation solutions.
|